Archive - Car Tools
Choose an alternative in the category
Car Tools
1,374
Results
LED Flashlight - Rechargeable LED workshop lamp, length 320 mm, equipped with main COB-LED 5W + 5 LEDs, lithium cells with a voltage of 3.7 V and a capacity of 2600 mAh, equipped with three strong neodymium magnets, the possibility of changing the angle in the range of 170 degrees, additional retractable hook for hanging, The battery is charged via micro USB
Discontinued
Order Code:
AUPR82462
LED Flashlight - equipped with 3 COB-LEDs, cable length 180 cm, industrial protection IP54, dimensions after folding: 260 × 230 × 40 mm, voltage 230 V, power 30 + 20 W, COB-LED type, number of diodes: 3, luminous flux 4500 lm, cable length 180 cm, number of degrees of angle change: 8, Protection class IP54, weight 1715 g
Discontinued
Order Code:
AUPR82464
LED Flashlight - suitable for checking the leak tightness of the air conditioning system (UV), magnetic base rotatable 360°, USB charging cable + charger, LED output 620 lumens, Charger 5.0 V 2000 mAh / AC100 ~ 240 V 50/60 Hz, Charging time 3.5 hours, Activity time 3 h +, 3350 mAh battery, size 477 × 50 × 40 mm, weight 295 g
Discontinued
Order Code:
AUPR82465
LED Flashlight - Rechargeable workshop lamp with adjustable 3in1 lamp power, flashlight, POWER BANK, 180° adjustable leg with strong magnet, Light emitted by 5W COB-LED in torch mode and 3 LEDs in flashlight mode, clip connected to the magnet, power supply via USB cable, which is included in the set, 2000 mAh lithium battery, dimensions 190 × 55 × 25 mm, weight 260 g
Discontinued
Order Code:
AUPR82463
Puller - Rear axle puller Toyota YARIS 2005-2011 is used only for pressing bushings on the car
Discontinued
Order Code:
AUPR82422
Puller - kit for removing rear silentblocks on Ford Mondeo after 2007 and on 4x4 vehicles, the device is used to mount and dismount the bushings without removing the cross member
Discontinued
Order Code:
AUPR82424
Puller - press for removal and assembly of front lower control arm pivots Renault Scenic II, Clio III, IV, thread size: 18 mm, length 48 mm, width 48 mm, height 65 mm
Discontinued
Order Code:
AUPR82423
Puller - puller for mounting and dismounting wheel bearing and hub for VW ŠKODA AUDI, for diameter 72 mm, Designed for easy removal and precise mounting of the bearing in the hub, mounting plate has 8 holes, for vehicles: Audi A2, Skoda Fabia (2000), Volkswagen Polo and Fox (2005-), Seat Ibiza (2002-)
Discontinued
Order Code:
AUPR82421
Puller - puller for mounting and removing wheel bearing and hub, for 90 mm diameter ASTA A-H190, for easy and quick removal and precise mounting of the bearing to the axle hub, for Audi vehicles: A4/S4 Quattro Avant (2001-2008), A6/S6 Quattro Avant (2002-2005), A8/S8 Quattro Avant (2004-2007), R8 from 2007 onwards, quality design: made of chrome-vanadium (Cr-Mo) steel + S45C steel
Discontinued
Order Code:
AUPR82420
Puller - Hub puller FORD FOCUS II, VOLVO V50, set for mounting and dismounting bearings - wheel hubs with diameter 78 mm
Discontinued
Order Code:
AUPR82431
Puller - Brake disc puller for removing brake discs in the range of 170-400 mm, for brake discs with a diameter of 170-400 mm, for quick and safe removal of brake discs, mounting the arms on springs makes installation easier, Reduces vibration load on wheel bearings, electronic sensors, ball joints, etc, hardened material
Discontinued
Order Code:
AUPR82416
Puller - forged puller for removing ball pins and ball joints in the range of 35-62 mm, screw for adjusting the working range, stabilizing springs, narrow feet facilitate access to confined spaces, jaw width: 32 mm, working range: 35-62 mm
Discontinued
Order Code:
AUPR82413
Puller - clamp puller for removing hose clamps 8-60 mm, used for steel self-tensioning straps and hose clamps with a diameter of 8-60 mm, particularly useful in small, tight and hard-to-reach places
Discontinued
Order Code:
AUPR82432
Puller - set of three universal ball stud puller suitable especially for working in tight spaces, the ends of the screws are equipped with a ball, which reduces friction between them and the joint - the pin, puller size 23 × 55 mm, 6 edges for 17 mm wrench, 28 × 55 mm, 34 × 63 mm, 6 edges for 19 mm wrench, made of chromium-molybdenum (Cr-Mo) steel, packing: plastic case
Discontinued
Order Code:
AUPR82429
Discontinued
Order Code:
AUPR82363
Jack - lever, load capacity of 2000kg, lifting range: 135-335mm, weight: 8,7kg
Discontinued
Order Code:
MADZ897
Discontinued
Order Code:
CARaaa0241
Discontinued
Order Code:
CARaaa0240
Discontinued
Order Code:
CARaaa0239
Discontinued
Order Code:
CARaaa0227
Discontinued
Order Code:
CARaaa0226
Protective Cover , protective cover against scratches on painted parts of the car when working in the engine compartment
Discontinued
Order Code:
MOTO47913
Discontinued
Order Code:
AUPR72353
Discontinued
Order Code:
AUPRGM001